WEEK 22

Title : Build the Windbelt Frame Panel

Objective : Process of the to make Frame Panel

Content/Procedure :

• After making measurements on the drawing, I was hired a welder to complete the panel frame with a sketch by this project.

Result : 

The figure below shows the panel frame Windbelt completed according to specifications.

Completed panel frame.

 The diagram above shows a metal U is to bind the nylon belt attached to the magnet.

Stand for the windbelt frame panel.

Conclusion : Some problems have been solved during build and finally successful.

WEEK 21

Title: Build the Coil Winding

Objective: Process & Steps to make coil winding.

Content/Procedure:

After making a calculation to get 10V on coil by determining the resistance of the each coil of 200ohm.

This are neodyminium strong magnet which is rare earth magnet.

After completing each coils with resistance of 200 ohms, which is included with each magnet and nylon belt and I make the installation on this panel.

Result: The figure below shows the results of which are installed on a test panel to be tested before it is mounted on a steel panel.

Conclusion: There are several difficult things need to tested when I have build this project frame but finally it successful finish.

WEEK 20

Title: Assemble the AC/DC circuit.

Objective: Process & Steps to AC/DC circuit.

Content/Procedure:

After making testing on the breadboard, I use a circuit board to assemble the components.

Result: Figure below show the process to build the project outline.

Conclusion: There are several difficult things when I have build this project circuit but finally it successful finish.

WEEK 19

Title: Find The Electronic Components.

Objective: To Assemble The Circuit and Test It.

Content/Procedure:

This week, went to Jalan Pasar to buy several components like diode, capacitor, resistor wires and etc.

Result: Figure below show the sample for several components that I buy at Jalan Pasar.

Diode: A diode bridge is a device that changes alternating current(AC) from windbelt to Direct Current(DC) to batterry.

Capacitor: A capacitor is a passive two-terminal electrical component used to store energy electrostatically in an electric field.

Wires: I use several type of wires to make the connection for each components for my project.

Multimeter: To measure the current and voltage output produced by the vibration of the windbelt.

Conclusion: Hopefully, the components that I buy at Jalan Pasar will be function when it be to assemble together.

WEEK 18

Title: Project Sketching.

Objective: To Get the Best Project Design.

Content/Procedure:

Before to build the hardware for this project, I was made the first sketch for this project for wire connections, windbelt base, coils winding and other equipment that it can placed in a suitable position so that the project can functionally well.

Result:

Figure below show the project has been sketched and the wire connection in parallel to get the high current.

WEEK 17

Title: Simulate AC/DC Converter Circuit.

Objective: To estimate the input and output needed.

Content/Procedure:

Here is the circuit diagram of a  AC/DC converter. Before it use in my project, it should be simulate to determine that circuit function or not. The software to simulate this circuit is 'Multisim'.

Result: There are several result after simulation by using Multism Software.

Conclusion: 

Based on the results above, the circuit is functionally very well and it suitable in my project. The DC meter show the output value 15.402VDC. So, it prove this circuit can convert from 12VAC to 15VDC.

WEEK 16

Title: Discuss with Supervisor.

Objective: Step Needed to Start

Content/Procedure:

When the new semester was open after semester break almost 3 month, I have go to see my supervisor, Sir Mohd Akram Dandu and making some little discussion.

Result: After discussion with supervisor, I have know what the first step need to do for my Final Year Project 2 (FYP 2).

Conclusion: Hopefully, I can do the my project very well by following the timeline given.